Flowserve WXCL UltraSwitch Uživatelský manuál stáhnout pdf (Strana 1)

Description:

Worcester Controls UltraSwitch™ limit switch enclosures provide local and remote position indication for

automated valves. They generally feature a visual indicator with “red=closed” and “green=open” for intuitive

local position determination. The UltraSwitch™ is available with a number of limit switch options for remote

indication in a variety of electrical applications. They may also be used as a junction box for direct

installation of solenoid valves.

Installation:

UltraSwitches may be installed to valves or valve actuators with a variety of mounting hardware. For best

results, specify the NAMUR shaft option and NAMUR mounting hardware when installing to NAMUR

compliant actuator. These options allow direct coupling to actuators

without couplings, reducing dead band.

Simply bolt bracket to actuator and UltraSwitch™ to bracket, leaving bolts finger tight. For NAMUR applications

the UltraSwitch™ shaft features an integral alignment pin. This pin must engage the tapped hole in the actuator

shaft. For non-NAMUR applications, make

sure to properly install a coupler between UltraSwitch™ and actuator. Once the UltraSwitch™ is installed with

fasteners loosely tightened, stroke the actuator two or three times to align the bracket. Then tighten all fasteners.

Wiring Instructions:

UltraSwitch™ enclosures feature pre-wired switches. All user connections are made at a numbered terminal

strip. Both external bonding and internal grounding locations have been provided for use in installation. A

wiring diagram is located inside the cover and indicates which terminal numbers correspond to switch

contacts: normally open, normally closed, common, etc. Simply follow the wiring diagram and electric code to

connect switches to your system.

For field wiring: ensure that any excess wire lengths or loops are routed away from any moving parts and are

short enough, or secured to ensure a ¼” clearance between the wire and the inside surface of the switchbox

cover.

Note: for all magnetically tripped proximity switches, the top switch (top and third switches for 4-switch

versions) should only be used to indicate the clockwise position: the bottom switch (second and fourth

switches for 4-switch versions) should only be used to indicate the counter-clockwise position. Any deviation

from these settings may result in erratic indication.

Solenoids may also be wired through the UltraSwitch™ enclosure. At least two auxiliary terminals are included as

standard.

Worcester Controls

Installation

Operation

Maintenance

UltraSwitch™ WXCL/WXML

FCD WCENIM2076-05

1 2 3 4 5 6 ... 10 11

Shrnutí obsahu

Strany 1 - Maintenance

S Description: Worcester Controls UltraSwitch™ limit switch enclosures provide local and remote position indication for automated valves. They

Strany 2 - Adjusting Limit Switches:

Max Safe Gaps: GA Drawings. Flamepath Maximum Gap (mm) Comment Cover and base 0.038 Flanged joint Operating rod and cove

Strany 3

Bulletin FCD WCENIM2076-05 Flowserve Corporation Cookeville, Tennessee, USA, 38501 931 432-4021 Flowserve Flow Control UK Ltd Haywards Heath

Strany 4

A ground screw is also included. Simply wire the solenoid to auxiliary terminals, then connect power leads to the opposite terminal side. Be sur

Strany 5

Fine Cam Adjustment: Some cams have a fine adjustment available. These cams will have a small screw embedded into the side of the cam. Adjustin

Strany 6 -  INDICATOR TYPE

Switch Option Specifications: Switch Option Manufacturer Part Number Load Capacity M1 – SPDT Mechanical Honeywell MicroSwitch V7-1C13D8-201 15.

Strany 7 -  CERTIFICATIONS

Analog Feedback Option Specifications: Options T, D, E, S - 4-20 mA Transmitter Voltage Supply: 6-30 VAC Impedance: 300 Ohms at 20 mA Optio

Strany 8 -  COATING OPTIONS

Product Nomenclature:  Prefix W - Worcester Controls  SHAFT TYPE D - Double “D” Shaft N - NAMUR Shaft M - 0.085 Double “D”

Strany 9

 SWITCH ELEMENT TYPE 00 - No Switches (empty housing) M1 - SPDT Mechanical MA - SPDT Mechanical with Cams for 3-Position control (s

Strany 10

 ANALOG OUTPUT OPTIONS - (see note 3) -0 - None -T - 4-20mA Transmitter (40’ to 100’ travel) -D - 180’ Travel 4-20mA Transmit

Strany 11 - WCENIM2076-05

Notes 1) MA switch element must be ordered with qty. (2) switch elements. MD and MS switch elements must be ordered with qty. (4) switch

Příbuzné modely WXML UltraSwitch | AXCL UltraSwitch | AXML UltraSwitch |

Komentáře k této Příručce

Žádné komentáře

Flowserve WXCL UltraSwitch Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Flowserve WXCL UltraSwitch. Flowserve WXCL UltraSwitch User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely WXML UltraSwitch | AXCL UltraSwitch | AXML UltraSwitch |

Komentáře k této Příručce

Flowserve WXCL UltraSwitch Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Flowserve WXCL UltraSwitch. Flowserve WXCL UltraSwitch User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely WXML UltraSwitch | AXCL UltraSwitch | AXML UltraSwitch |

Komentáře k této Příručce

Související produkty a manuály pro Hardware Flowserve WXCL UltraSwitch